SheevaPlug initial bootlog

Marc Nozell — Wed, 13 May 2009 18:37:13 +0000

__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** MARVELL BOARD: SHEEVA PLUG LE U-Boot 1.1.4 (Mar 19 2009 - 16:06:59) Marvell version: 3.4.16 U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE80 Soc: 88F6281 A0 (DDR2) CPU running @ 1200Mhz L2 running @ 400Mhz SysClock = 400Mhz , TClock = 200Mhz DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6 DRAM CS[0] base 0x00000000 size 256MB DRAM CS[1] base 0x10000000 size 256MB DRAM Total size 512MB 16bit width Flash: 0 kB Addresses 8M - 0M are saved for the U-Boot usage. Mem malloc Initialization (8M - 7M): Done NAND:512 MB CPU : Marvell Feroceon (Rev 1) Streaming disabled Write allocate disabled USB 0: host mode PEX 0: interface detected no Link. Net: egiga0 [PRIME], egiga1 Hit any key to stop autoboot: 3 NAND read: device 0 offset 0x100000, size 0x400000 Reading data from 0x100000 -- 0% complete. Reading data from 0x10a000 -- 1% complete. Reading data from 0x114000 -- 2% complete. Reading data from 0x11e800 -- 3% complete. Reading data from 0x128800 -- 4% complete. Reading data from 0x133000 -- 5% complete. Reading data from 0x13d000 -- 6% complete. Reading data from 0x147800 -- 7% complete. Reading data from 0x151800 -- 8% complete. Reading data from 0x15c000 -- 9% complete. Reading data from 0x166000 -- 10% complete. Reading data from 0x170800 -- 11% complete. Reading data from 0x17a800 -- 12% complete. Reading data from 0x185000 -- 13% complete. Reading data from 0x18f000 -- 14% complete. Reading data from 0x199800 -- 15% complete. Reading data from 0x1a3800 -- 16% complete. Reading data from 0x1ae000 -- 17% complete. Reading data from 0x1b8000 -- 18% complete. Reading data from 0x1c2800 -- 19% complete. Reading data from 0x1cc800 -- 20% complete. Reading data from 0x1d7000 -- 21% complete. Reading data from 0x1e1000 -- 22% complete. Reading data from 0x1eb800 -- 23% complete. Reading data from 0x1f5800 -- 24% complete. Reading data from 0x1ff800 -- 25% complete. Reading data from 0x20a000 -- 26% complete. Reading data from 0x214000 -- 27% complete. Reading data from 0x21e800 -- 28% complete. Reading data from 0x228800 -- 29% complete. Reading data from 0x233000 -- 30% complete. Reading data from 0x23d000 -- 31% complete. Reading data from 0x247800 -- 32% complete. Reading data from 0x251800 -- 33% complete. Reading data from 0x25c000 -- 34% complete. Reading data from 0x266000 -- 35% complete. Reading data from 0x270800 -- 36% complete. Reading data from 0x27a800 -- 37% complete. Reading data from 0x285000 -- 38% complete. Reading data from 0x28f000 -- 39% complete. Reading data from 0x299800 -- 40% complete. Reading data from 0x2a3800 -- 41% complete. Reading data from 0x2ae000 -- 42% complete. Reading data from 0x2b8000 -- 43% complete. Reading data from 0x2c2800 -- 44% complete. Reading data from 0x2cc800 -- 45% complete. Reading data from 0x2d7000 -- 46% complete. Reading data from 0x2e1000 -- 47% complete. Reading data from 0x2eb800 -- 48% complete. Reading data from 0x2f5800 -- 49% complete. Reading data from 0x2ff800 -- 50% complete. Reading data from 0x30a000 -- 51% complete. Reading data from 0x314000 -- 52% complete. Reading data from 0x31e800 -- 53% complete. Reading data from 0x328800 -- 54% complete. Reading data from 0x333000 -- 55% complete. Reading data from 0x33d000 -- 56% complete. Reading data from 0x347800 -- 57% complete. Reading data from 0x351800 -- 58% complete. Reading data from 0x35c000 -- 59% complete. Reading data from 0x366000 -- 60% complete. Reading data from 0x370800 -- 61% complete. Reading data from 0x37a800 -- 62% complete. Reading data from 0x385000 -- 63% complete. Reading data from 0x38f000 -- 64% complete. Reading data from 0x399800 -- 65% complete. Reading data from 0x3a3800 -- 66% complete. Reading data from 0x3ae000 -- 67% complete. Reading data from 0x3b8000 -- 68% complete. Reading data from 0x3c2800 -- 69% complete. Reading data from 0x3cc800 -- 70% complete. Reading data from 0x3d7000 -- 71% complete. Reading data from 0x3e1000 -- 72% complete. Reading data from 0x3eb800 -- 73% complete. Reading data from 0x3f5800 -- 74% complete. Reading data from 0x3ff800 -- 75% complete. Reading data from 0x40a000 -- 76% complete. Reading data from 0x414000 -- 77% complete. Reading data from 0x41e800 -- 78% complete. Reading data from 0x428800 -- 79% complete. Reading data from 0x433000 -- 80% complete. Reading data from 0x43d000 -- 81% complete. Reading data from 0x447800 -- 82% complete. Reading data from 0x451800 -- 83% complete. Reading data from 0x45c000 -- 84% complete. Reading data from 0x466000 -- 85% complete. Reading data from 0x470800 -- 86% complete. Reading data from 0x47a800 -- 87% complete. Reading data from 0x485000 -- 88% complete. Reading data from 0x48f000 -- 89% complete. Reading data from 0x499800 -- 90% complete. Reading data from 0x4a3800 -- 91% complete. Reading data from 0x4ae000 -- 92% complete. Reading data from 0x4b8000 -- 93% complete. Reading data from 0x4c2800 -- 94% complete. Reading data from 0x4cc800 -- 95% complete. Reading data from 0x4d7000 -- 96% complete. Reading data from 0x4e1000 -- 97% complete. Reading data from 0x4eb800 -- 98% complete. Reading data from 0x4f5800 -- 99% complete. Reading data from 0x4ff800 -- 100% complete. 4194304 bytes read: OK ## Booting image at 00800000 ... Image Name: Linux-2.6.22.18 Created: 2009-03-19 9:18:16 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2106696 Bytes = 2 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK Starting kernel ... Uncompressing Linux.................................................................................................................................... done, booting the kernel. Linux version 2.6.22.18 (dhaval@devbox) (gcc version 4.2.1) #1 Thu Mar 19 14:46:22 IST 2009 CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177 Machine: Feroceon-KW Using UBoot passing parameters structure Memory policy: ECC disabled, Data cache writeback CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets Built 1 zonelists. Total pages: 130048 Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) rw root=/dev/mtdblock1 rw ip=10.4.50.4:10.4.50.5:10.4.50.5:255.255.255.0:DB88FXX81:eth0:none PID hash table entries: 2048 (order: 11, 8192 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 256MB 256MB 0MB 0MB = 512MB total Memory: 515456KB available (3864K code, 257K data, 104K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 CPU Interface ------------- SDRAM_CS0 ....base 00000000, size 256MB SDRAM_CS1 ....base 10000000, size 256MB SDRAM_CS2 ....disable SDRAM_CS3 ....disable PEX0_MEM ....base e8000000, size 128MB PEX0_IO ....base f2000000, size 1MB INTER_REGS ....base f1000000, size 1MB NFLASH_CS ....base fa000000, size 2MB SPI_CS ....base f4000000, size 16MB BOOT_ROM_CS ....no such DEV_BOOTCS ....no such CRYPT_ENG ....base f0000000, size 2MB Marvell Development Board (LSP Version KW_LSP_4.2.7_patch2)-- SHEEVA PLUG Soc: 88F6281 A0 LE Detected Tclk 200000000 and SysClk 400000000 MV Buttons Device Load Marvell USB EHCI Host controller #0: c08b8600 PEX0 interface detected no Link. PCI: bus0: Fast back to back transfers enabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 Time: kw_clocksource clocksource has been installed. IP route cache hash table entries: 16384 (order: 4, 65536 bytes) TCP established hash table entries: 65536 (order: 7, 524288 bytes) TCP bind hash table entries: 65536 (order: 6, 262144 bytes) TCP: Hash tables configured (established 65536 bind 65536) TCP reno registered RTC registered Use the XOR engines (acceleration) for enhancing the following functions: o RAID 5 Xor calculation o kernel memcpy o kenrel memzero Number of XOR engines to use: 4 cesadev_init(c000c894) mvCesaInit: sessions=640, queue=64, pSram=f0000000 Warning: TS unit is powered off. MV Buttons Driver Load NTFS driver 2.1.28 [Flags: R/O]. JFFS2 version 2.2. (NAND) 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A Loading Marvell Ethernet Driver: o Cached descriptors in DRAM o DRAM SW cache-coherency o Single RX Queue support - ETH_DEF_RXQ=0 o Single TX Queue support - ETH_DEF_TXQ=0 o TCP segmentation offload enabled o Receive checksum offload enabled o Transmit checksum offload enabled o Network Fast Processing (Routing) supported o Driver ERROR statistics enabled o Driver INFO statistics enabled o Proc tool API enabled o Rx descripors: q0=128 o Tx descripors: q0=532 o Loading network interface(s): o eth0, ifindex = 1, GbE port = 0 o eth1, ifindex = 2, GbE port = 1 mvFpRuleDb (dfd00000): 16384 entries, 65536 bytes Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI Copyright (c) 1999-2006 Intel Corporation. e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI e100: Copyright(c) 1999-2006 Intel Corporation Warning Sata is Powered Off NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $ NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit) Scanning device for bad blocks Bad eraseblock 372 at 0x02e80000 Bad eraseblock 2158 at 0x10dc0000 Bad eraseblock 2419 at 0x12e60000 Bad eraseblock 2420 at 0x12e80000 Bad eraseblock 2439 at 0x130e0000 2 cmdlinepart partitions found on MTD device nand_mtd Using command line partition definition Creating 2 MTD partitions on "nand_mtd": 0x00100000-0x00500000 : "uImage" 0x00500000-0x20000000 : "rootfs" ehci_marvell ehci_marvell.70059: Marvell Orion EHCI ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1 ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100 ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected USB Universal Host Controller Interface driver v3.0 usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice i2c /dev entries driver Linux telephony interface: v1.00 Marvell Telephony Driver: mvBoardVoiceAssembleModeGet: TDM not supported(boardId=0x9) assembly=-1,irq=-1 mp_check_config: Error, invalid voice assembley mode md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 raid6: int32x1 97 MB/s raid6: int32x2 114 MB/s raid6: int32x4 122 MB/s raid6: int32x8 110 MB/s raid6: using algorithm int32x4 (122 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: measuring checksumming speed arm4regs : 1071.600 MB/sec 8regs : 754.800 MB/sec 32regs : 900.000 MB/sec raid5: using function: arm4regs (1071.600 MB/sec) device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com dm_crypt using the OCF package. sdhci: Secure Digital Host Controller Interface driver sdhci: Copyright(c) Pierre Ossman mvsdmmc: irq =28 start f1090000 mvsdmmc: no IRQ detect usbcore: registered new interface driver usbhid drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC). mvCLAudioCodecRegGet: Error while reading register! mvCLAudioCodecInit: Error - Invalid Cirrus Logic chip/rev ID! Error - Cannot initialize audio decoder.at address =0xff<6>ALSA device list: #0: Marvell mv88fx_snd ALSA driver TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 mmc0: host does not support reading read-only switch. assuming write-enable. mmc0: new SD card at address d3cb mmcblk0: mmc0:d3cb SD02G 1985024KiB mmcblk0: p1 eth0: link down eth0: started IP-Config: Complete: device=eth0, addr=10.4.50.4, mask=255.255.255.0, gw=10.4.50.5, host=DB88FXX81, domain=, nis-domain=(none), bootserver=10.4.50.5, rootserver=10.4.50.5, rootpath= md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. eth0: link up, half duplex, speed 10 Mbps Empty flash at 0x087fd338 ends at 0x087fd800 Empty flash at 0x0f3869a0 ends at 0x0f387000 VFS: Mounted root (jffs2 filesystem). Freeing init memory: 104K * Setting preliminary keymap... [80G [74G[ OK ] * Setting the system clock The Hardware Clock does not contain a valid time, so we cannot set the System Time from it. Unable to set system clock. [33m* [39;49m Unable to set System Clock to: Sun Jun 23 11:17:01 UTC 1963 * Starting basic networking... [80G [74G[ OK ] * Starting kernel event manager... [80G [74G[ OK ] * Loading hardware drivers... [80G [74G[ OK ] * Setting the system clock The Hardware Clock does not contain a valid time, so we cannot set the System Time from it. Unable to set system clock. [33m* [39;49m Unable to set System Clock to: Sun Jun 23 11:17:04 UTC 1963 * Loading kernel modules... [80G * Loading manual drivers... [80G [74G[ OK ] * Setting kernel variables (/etc/sysctl.conf)... [80G [74G[ OK ] * Setting kernel variables (/etc/sysctl.d/10-console-messages.conf)... [80G [74G[ OK ] * Setting kernel variables (/etc/sysctl.d/10-network-security.conf)... [80G [74G[ OK ] * Setting kernel variables (/etc/sysctl.d/10-process-security.conf)... [80G error: "vm.mmap_min_addr" is an unknown key [74G[ [31mfail [39;49m] * Setting kernel variables (/etc/sysctl.d/10-tcp-timestamps-workaround.conf)... [80G [74G[ OK ] * Activating swap... [80G [74G[ OK ] FATAL: Could not load /lib/modules/2.6.22.18/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.22.18/modules.dep: No such file or directory * Starting early crypto disks... [80G [74G[ OK ] FATAL: Could not load /lib/modules/2.6.22.18/modules.dep: No such file or directory FATAL: Could not load /lib/modules/2.6.22.18/modules.dep: No such file or directory * Starting remaining crypto disks... [80G [74G[ OK ] * Checking file systems... [80G fsck 1.41.3 (12-Oct-2008) [74G[ OK ] * Mounting local filesystems... [80G [74G[ OK ] * Activating swapfile swap... [80G [74G[ OK ] * Configuring network interfaces... [80G [74G[ OK ] * Setting up console font and keymap... [80G [74G[ OK ] * Starting system log daemon... [80G Ubuntu jaunty (development branch) debian ttyS0 debian login: [74G[ OK ] * Starting kernel log daemon... [80G [74G[ OK ] * Starting OpenBSD Secure Shell server sshd [80G [74G[ OK ] * Starting periodic command scheduler crond [80G [74G[ OK ] fat: exports duplicate symbol fat_add_entries (owned by kernel) insmod: error inserting '/boot/fat.ko': -1 Invalid module format

Nozell, rhymes with Oh Hell » boot log

SheevaPlug initial bootlog